ASME B18.6.3 Slotted Undercut Oval Countersunk Head Machine Screws

ASME B18.6.3 Slotted Undercut Oval Countersunk Head Machine Screws

Dimensions of ASME B18.6.3 Slotted Undercut Oval Countersunk Head Machine Screws

Nominal Size or Basic Screw Diameter Length, L Head Diameter, A Head Side Height, H Head Crown Height, C Total Head Height, O Slot Width, J Slot Depth, T Protrusion Above Gaging Diameter, F Gaging Diameter, G
Max Min Max Min Max Min Max Min Max Min
0 1/8 0.112 0.096 0.025 0.021 0.046 0.033 0.023 0.016 0.028 0.022 0.047 0.031 0.078
1 1/8 0.137 0.120 0.031 0.025 0.056 0.042 0.026 0.019 0.034 0.027 0.053 0.035 0.101
2 1/8 0.162 0.144 0.036 0.029 0.065 0.050 0.031 0.023 0.040 0.033 0.058 0.039 0.124
3 1/8 0.187 0.167 0.042 0.033 0.075 0.059 0.035 0.027 0.047 0.038 0.064 0.044 0.148
4 3/16 0.212 0.191 0.047 0.037 0.084 0.067 0.039 0.031 0.053 0.043 0.069 0.048 0.172
5 3/16 0.237 0.215 0.053 0.041 0.094 0.076 0.043 0.035 0.059 0.048 0.075 0.053 0.196
6 3/16 0.262 0.238 0.059 0.045 0.104 0.084 0.048 0.039 0.065 0.053 0.080 0.057 0.220
8 1/4 0.312 0.285 0.070 0.052 0.123 0.101 0.054 0.045 0.078 0.064 0.091 0.066 0.267
10 5/16 0.362 0.333 0.081 0.060 0.142 0.118 0.060 0.050 0.090 0.074 0.102 0.075 0.313
12 3/8 0.412 0.380 0.092 0.068 0.161 0.135 0.067 0.056 0.103 0.085 0.113 0.084 0.362
1/4 7/16 0.477 0.442 0.107 0.079 0.186 0.158 0.075 0.064 0.119 0.098 0.129 0.095 0.424
5/16 1/2 0.597 0.556 0.134 0.099 0.232 0.198 0.084 0.071 0.149 0.124 0.155 0.117 0.539
3/8 9/16 0.717 0.670 0.161 0.117 0.278 0.239 0.094 0.081 0.179 0.149 0.182 0.139 0.653
7/16 5/8 0.760 0.715 0.156 0.122 0.279 0.239 0.094 0.081 0.184 0.154 0.195 0.150 0.690
1/2 3/4 0.815 0.765 0.156 0.131 0.288 0.244 0.106 0.091 0.204 0.169 0.212 0.163 0.739

Note :

  • Where specifying nominal size in decimals, zeros preceding the decimals and in the fourth decimal place shall be omitted.
  • Screws of these lengths and shorter are undercut. Screws of longer lengths shall have head heights.
  • Tabulated values determined from formula for maximum H, Appendix A.
  • No tolerance for gaging diameter is given. If the gaging diameter of the gage used differs from tabulated value, the protrusion will be affected accordingly and the proper protusion values must be recalculated using the formulas.